j series jf illuminated ultra-thin process sealed tactiles www.nkk.com j40 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt toggles electrical capacity (resistive load) low/logic level: 50ma @ 24v dc other ratings contact resistance: 50 milliohms maximum insulation resistance: 500 megohms minimum @ 250v dc dielectric strength: 250v ac minimum for 1 minute minimum mechanical life: 500,000 operations minimum electrical life: 500,000 operations minimum nominal operating force: 3.0n for fush actuator 2.0n for sculptured actuator total travel: flush actuators .016 (0.4mm); sculptured actuator: .031 (0.8mm) materials & finishes actuator: polyamide for spot illuminated; polycarbonate for full face case: glass fber reinforced polyamide seal: nitrile butadiene rubber base: glass fber reinforced polyester movable contact: phosphor bronze with silver plating stationary contacts: brass with silver plating terminals: brass with silver plating environmental data operating temperature range: C25c through +70c (C13f through +158f) humidity: 90 ~ 95% humidity for 96 hours @ 40c (104f) vibration: 10 ~ 55hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours shock: 50g (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) pcb processing soldering: wave soldering recommended. see profle a in supplement section. manual soldering: see profle a in supplement section. cleaning: automated cleaning. see cleaning specifcations in supplement section. switches should not be operated or have any pressure on the actuators during cleaning. full face illuminated models suitable only for bottom board spray wash to avoid contamination of the 2-layered actuator, which may compromise the aesthetics. standards & certifcations the jf series tactiles have not been tested for ul recognition or csa certifcation. these switches are designed for use in a low-voltage, low-current, logic-level circuit. when used as intended in a logic-level circuit, the results do not produce hazardous energy. general specifcations
j series jf illuminated ultra-thin process sealed tactiles www.nkk.com j42 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt toggles pole & circuit 15 spst off (on) ( ) = momentary typical switch ordering example 15 c jf spst off-(on) circuit illumination r spot a full face (with square actuator only) r description for typical ordering example jf15rp2cc p 2 terminals p straight pc actuator types 1 square 2 round 3 sculptured led colors c red e yellow f green pole & circuit actuator position ( ) = momentary switch throw & schematic led schematic pole model normal down spst notes: terminal numbers are shown on switch. led circuit is isolated & requires external power source. sp jf15 off (on) red led for spot illumination round red actuator (+) (-) 1 2 3 4 c actuator colors spot illuminated c red d orange f green g blue h gray *full face illuminated c red e yellow f green *led color must match actuator color. straight pc terminals
j series jf illuminated ultra-thin process sealed tactiles www.nkk.com j43 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt toggles illumination & actuator types flexible panel design versatile panel arrangements can be made to ft individual design needs. terminals with isolated lamp circuit further details in typical switch dimensions p straight pc terminals led colors & specifications r spot illumination a full face illumination 1 square actuator 1 2 round actuator 3 sculptured actuator actuator colors available: c, d, f, g, h housing is black actuator colors available: c, e, f housing is black square actuator color codes: red orange yellow green blue c d e f g gray h (17.78) ty p .700 (27.94) 1.100 (1.04) .041 (1.7) .067 (5.08) .200 (3.6) .142 (6.0) min .236 (5.72) .225 (17.78) ty p .700 (22.86) .900 (6.7) .264 (3.6) .142 (7.3) .287 (3.0) .118 spot illumination full face illumination led polarity marking leds are supplied as an integral part of the switch. the electrical specifcations shown are determined at a basic temperature of 25c. if the source voltage exceeds the rated voltage, a ballast resistor is required. the resistor value can be calculated by using the formula in the supplement section. spot illumination full face illumination color red yellow green red yellow green forward peak current i fm 40ma 40ma 40ma 30ma 30ma 30ma continuous forward current i f 30ma 30ma 30ma 20ma 20ma 20ma forward voltage v f 1.7v 2.2v 2.2v 1.77v 2.1v 2.3v reverse peak voltage v rm 4v 4v 4v 4v 4v 4v current reduction rate above 25c ?i f 0.67ma/c 0.67ma/c 0.67ma/c 0.4ma/c 0.4ma/c 0.4ma/c ambient temperature range C25 ~ +70c C25 ~ +70c e f c e f c
j series jf illuminated ultra-thin process sealed tactiles www.nkk.com j44 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt toggles jf15rp3cc jf15ap1cc typical switch dimensions spot illuminated with square actuator spot illuminated with round actuator jf15rp1cc jf15rp2cc (5.08) .200 (0.2) ty p .008 (10.16) .400 (0.8) ty p .031 1 3 2 4 (3.0) .118 (0.5) .020 (5.08) .200 (12.7) .500 (0.3) ty p .012 (3.6) .142 (8.68) .342 (0.3) .012 (5.7) .225 (6.0) min .236 (13.95) .549 (11.43) .450 (2.2) .087 (5.6) .220 (1.6) .063 (3.8) .150 (14.0) sq .551 (17.7) .697 (16.4) sq .646 (8.85) .348 (10.16) .400 (0.8) ty p .031 (5.08) .200 (0.2) ty p .008 1 3 2 4 (3.0) .118 (0.5) .020 (5.08) .200 (12.7) .500 (0.3) ty p .012 (3.6) .142 (8.68) .342 (0.3) .012 (5.7) .225 (6.0) min .236 (13.95) .549 (11.43) .450 (2.2) .087 (5.6) .220 (1.6) .063 (3.8) .150 (14.0) dia .551 (17.7) .697 (16.4) sq .646 (8.85) .348 (5.08) .200 (0.2) ty p .008 (10.16) .400 (0.8) ty p .031 1 3 2 4 (12.7) .500 (3.0) .118 (0.5) .020 (5.08) .200 (0.3) .012 (1.7) .067 (8.68) .342 (3.6) .142 (0.3) ty p .012 (5.7) .225 (6.0) min .236 (14.0) sq .551 (8.85) .348 (11.43) .450 (13.95) .549 (17.7) .697 (16.4) sq .646 (2.2) .087 (5.6) .220 (1.6) .063 (3.8) .150 (5.08) .200 (10.16) .400 (0.8) ty p .031 ? + 1 3 2 4 (10.16) .400 (0.3) .012 (0.3) ty p .012 (3.6) .142 (10.3) .406 (12.7) .500 (7.3) .287 (3.0) min .118 (3.0) .118 (0.5) sq .020 (8.85) .348 (13.5) .531 (2.7) .106 (6.0) .236 (7.3) .287 (8.2) .323 (16.4) .646 (17.7) .697 (13.0) sq .512 (26.9) 1.059 3 1 2 4 + _ (12.7) .500 (10.16) .400 (1.0) dia ty p .039 (5.08) .200 (5.08) .200 3 1 2 4 + _ (12.7) .500 (10.16) .400 (1.0) dia ty p .039 (5.08) .200 (5.08) .200 3 1 2 4 + _ (12.7) .500 (10.16) .400 (1.0) dia ty p .039 (5.08) .200 (5.08) .200 spot illuminated with sculptured actuator full face illuminated with square actuator +? 1 3 4 2 (10.16) .400 (1.0) dia ty p .039 (12.7) .500 (10.16) .400 (5.08) .200
j series jf illuminated ultra-thin process sealed tactiles www.nkk.com j45 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable rockers touch tilt toggles legends suggested printable area recommended print method: screen print or pad print epoxy based ink is recommended. shaded areas are printable areas. (13.0) sq .512 (11.48) sq .452 (6.0) .236 (4.48) .176 (13.5) .531 (11.98) .472 (0.76) ty p .030 (0.76) ty p .030 (0.76) ty p .030 power power on on down (12.48) dia .491 (14.0) dia .551 (0.76) ty p .030 (8.03) .316 (11.13) .438 (4.98) .196 (9.6) .378 (1.52) ty p .060 (0.76) ty p .030 (14.0) sq .551 (12.48) sq .491 (0.76) ty p .030 nkk switches can provide custom legends for caps. contact factory for more information.
|
